Infrared Sensor T8 LED Tube Light

The infrared sensor T8 LED tube light is designed with imported technology MCU circuit, with active infrared working mode and infrared decoding method, which make the lamp with the characteristics of good stability, strong anti-interference etc. It is widely used in commercial and industrial occasions which with higher requirement, and become a new generation of green energy-saving lighting fixtures. The lighting can be turned on automatically if a person entered into the sensor range, while leave (after 15s~30s), the light will keep 10% brightness then work at a low watt of 3W or turn off. In this way, artificial waste of energy was prevented and thus extend the service life of electrical appliances, and integrate energy saving and security functions.

Light Victor Infrared sensor LED tube light driver

Infrared Sensor LED tube light driver Human body induction receiving head with Fresnel filter lens, to collect the infrared energy changes of the environment. It adopts one-transmit-one-receive active infrared technology, integrated codec transmission and decoding receiving, control output, powerful 8-bit single-chip microcomputer production function, industrial district-level chip, wide load capacity, strong anti-interference ability. It is suitable for any place.

Light Victor sensor LED tube mode instruction

1. Static lighting mode

When there are no vehicles or people entering or exiting, all microwave radar LED lamps are in a dormant state, and power consumption of each tube is only 10% brightness, which not only meets the requirements of security monitoring lighting, but also greatly saves electricity.

2. Dynamic lighting mode

When a vehicle enters and exits, the microwave radar on the LED tube light in the corresponding area received the signal, and the dormant LED tube will be immediately awakened and light up at 100% brigtness, which is convenient for the owner to stop.

3. Brightness (Daylight) Sensor

With brightness sensor, the motion sensor will only work at night, even if there is movement at daytime, the light will not light up.

Data sheet of infrared human body sensor T8 LED tube light

Light victor sensor tube light advantages

1. Intelligent induction control, more energy saving

2. Stable induction, less susceptible to external interference, better in penetrating.

3. With Superior quality aluminum housing can help for better heat sink, and plastic cover can achieve high light luminousness, which all work on lengthen the service life and at the same time they are recyclable.

4. LED chips' service life can be up to 50000 hours.

5. Special irritation angle mixed design.

6. Immediately light up，no flicker, no noises；

7. Built-in high precision constant current power supply, with efficiency high up to 90%. With protector, which can help to work under unstable voltage.

8. Special circuit design, can avoid depress because of single LED chip breakdown.

9. No fluorescence blinking, no mercury.

LED Tube light packing and installation

Special installation remind

1) It is normal that there will be three times consecutive lighting on when the power turned on for the first time t. The light will not be on rightly during the daytime or when the light is strong. The light will automatically turn on when people arrive at night or when the light is dark. In the daytime, if covering the infrared probe lens tightly with a black cloth for more ten seconds (not allowing it to transmit light), you can also try to light it up.

2) When installing, please install the smart lamp in a place where people often move (ceiling or wall) to improve its sensitivity and working range. Do not install on a damp ceiling or wall.

3) Disconnect the power supply first when cleaning. Please choose non-corrosive cleaning agent when cleaning.

4) After the lamp is installed, acidic or alkaline chemical solvents cannot be used in a certain space, otherwise the electroplating or painting of the lamp will be damaged.

Infrared motion sensor T8 LED tube light application

This T8 Light is very sensitive. Which make it perfect for places that no need of ever last lighting like parking lot, basement, corridor and staircase of hotel, school, Supermarket, offices and hospitals. Moreover, places like storage area, under cabinet, doorway, toilet etc.

FAQ

Q1: When can I get the price?

A: Usually we quote within 24 hours after we get your inquiry.

Q2: Do you provide sample? Is it free?

A: If the sample is low value, we will provide the free sample with freight collect. But for some high value samples, we need to collect the sample charge.

Q3: How to proceed an order?

A: Customer inquiry=> Quotation within 24 hours=> Quotation acceptance=> Sampling (if needed) => Sample acceptance and deposit=> Mass production

Q4: Can I have a sample order for your product?

A: Yes, we welcome sample order to test and check quality. Mixed samples are acceptable.

Q5: What about the lead time?

A: Sample needs 3-5 days, mass production generally will need 10-15 days, and our on-time delivery rate is over 98%.

http://www.light-victor.com/